Global elevation data

The Land Processes Distributed Active Archive Center (LP DAAC) is responsible for the archive and distribution of NASA Making Earth System Data Records for Use in Research Environments (MEaSUREs) SRTM, which includes the global 3 arc second (~90 meter) product. The 3 arc second data was derived from the 1 arc second using averaging methods. (See Figure 3 in the User Guide) The NASA SRTM data sets result from a collaborative effort by the National Aeronautics and Space Administration (NASA) and the National Geospatial-Intelligence Agency (NGA - previously known as the National Imagery and Mapping Agency, or NIMA), as well as the participation of the German and Italian space agencies. This collaboration aims to generate a near-global digital elevation model (DEM) of Earth using radar interferometry. SRTM was the primary (and virtually only) payload on the STS-99 mission of the Space Shuttle Endeavour, which launched February 11, 2000 and flew for 11 days. The SRTM swaths extended from ~30 degrees off-nadir to ~58 degrees off-nadir from an altitude of 233 kilometers (km), creating swaths ~225 km wide, and consisted of all land between 60° N and 56° S latitude to account for 80% of Earth's total landmass. The SRTMGL3 data were generated from SRTM1GL data that fall within that tile. These elevation files use the extension ".HGT", meaning height (such as N37W105.SRTMGL3.HGT). The primary goal of creating the Version 3 data was to eliminate gaps, or voids, that were present in earlier versions of SRTM data. In areas with limited data, existing topographical data were used to supplement the SRTM data to fill the voids. The source of each elevation pixel is identified in the corresponding SRTMGL3N product (such as N37W105.SRTMGL3N.NUM). The global 3 arc second SRTM product is also available in NetCDF4 format as the SRTMGL3_NC dataset with the source of each elevation pixel in the corresponding SRTMGL3_NUMNC product. Known Issues * Known issues in the NASA SRTM are described in the following publication: * Rodriguez, E., C. S. Morris, and J. E. Belz (2006), A global assessment of the SRTM performance, Photogramm. Eng. Remote Sens., 72, 249–260. https://doi.org/10.14358/PERS.72.3.249

Digital Elevation Model cover: areas located between 0 and 10 meters above sea level. Pixels with a value lower than the specified threshold (0-10m) were given a value of 1 (YES response) ETOPO5 was generated from a digital data base of land and sea- floor elevations on a 5-minute latitude/longitude grid. **Data revision:** 2021-12-14 **Contact points:** Contact: [Giri Chandra](mailto:cgiri@usgs.gov) National Oceanic and Atmospheric Administration (NOAA) Metadata contact: [OCB Environment](mailto:OCB-Environment-List@fao.org) FAO-UN **Resource constraints:** license **Online resources:** National Oceanic and Atmospheric Administration (NOAA)

The Land Processes Distributed Active Archive Center (LP DAAC) is responsible for the archive and distribution of NASA Making Earth System Data Records for Use in Research Environments (MEaSUREs) SRTM, which includes the global 3 arc second (~90 meter) number product. The NASA SRTM data sets result from a collaborative effort by the National Aeronautics and Space Administration (NASA) and the National Geospatial-Intelligence Agency (NGA - previously known as the National Imagery and Mapping Agency, or NIMA), as well as the participation of the German and Italian space agencies. This collaboration aims to generate a near-global digital elevation model (DEM) of Earth using radar interferometry. SRTM was the primary (and virtually only) payload on the STS-99 mission of the Space Shuttle Endeavour, which launched February 11, 2000 and flew for 11 days. The SRTM swaths extended from ~30 degrees off-nadir to ~58 degrees off-nadir from an altitude of 233 kilometers (km), creating swaths ~225 km wide, and consisted of all land between 60° N and 56° S latitude to account for 80% of Earth's total landmass. Ancillary one-byte (0 to 255) "NUM" (number) files were produced for NASA SRTM Version 3. These files have names corresponding to the elevation files, except with the extension ".NUM" (such as N37W105.NUM). The elevation files use the extension ".HGT", meaning height (such as N37W105.HGT). The separate NUM file indicates the source of each DEM pixel; the number of ASTER scenes used (up to 100), if ASTER; and the number of SRTM data takes (up to 24), if SRTM. The NUM file for both 3 arc second products (whether sampled or averaged) references the 3 x 3 center pixel. Note that NUMs less than 6 are water and those greater than 10 are land. The 3 arc second data was derived from the 1 arc second using sampling and averaging methods. (See Figure 3 in the User Guide) The global 3 arc second number product is also available in NetCDF4 format as the SRTMGL3_NUMNC dataset and can be used with the corresponding SRTMGL3_NC elevation product. Known Issues * Known issues in the NASA SRTM are described in the following publication: * Rodriguez, E., C. S. Morris, and J. E. Belz (2006), A global assessment of the SRTM performance, Photogramm. Eng. Remote Sens., 72, 249–260. https://doi.org/10.14358/PERS.72.3.249

Rural land area below 5m is the total rural land area in square kilometers where the elevation is 5 meters or less.

The Land Processes Distributed Active Archive Center (LP DAAC) is responsible for the archive and distribution of NASA Making Earth System Data Records for Use in Research Environments (MEaSUREs) SRTM, which includes the global 3 arc second (~90 meter) sub-sampled product. The 3 arc second data was derived from the 1 arc second using sampling methods. (See Figure 3 in the User Guide) The NASA SRTM data sets result from a collaborative effort by the National Aeronautics and Space Administration (NASA) and the National Geospatial-Intelligence Agency (NGA - previously known as the National Imagery and Mapping Agency, or NIMA), as well as the participation of the German and Italian space agencies. This collaboration aims to generate a near-global digital elevation model (DEM) of Earth using radar interferometry. SRTM was the primary (and virtually only) payload on the STS-99 mission of the Space Shuttle Endeavour, which launched February 11, 2000 and flew for 11 days. The SRTMGL3 data were sub-sampled from SRTM1GL data that fall within that tile. These elevation files use the extension ".HGT", meaning height (such as N37W105.SRTMGL3S.HGT). The primary goal of creating the Version 3 data was to eliminate gaps, or voids, that were present in earlier versions of SRTM data. In areas with limited data, existing topographical data were used to supplement the SRTM data to fill the voids. The source of each elevation pixel is identified in the corresponding SRTMGL3N product (such as N37W105.SRTMGL3N.NUM). The SRTM swaths extended from ~30 degrees off-nadir to ~58 degrees off-nadir from an altitude of 233 kilometers (km), creating swaths ~225 km wide, and consisted of all land between 60° N and 56° S latitude to account for 80% of Earth's total landmass. Known Issues * Known issues in the NASA SRTM are described in the following publication: * Rodriguez, E., C. S. Morris, and J. E. Belz (2006), A global assessment of the SRTM performance, Photogramm. Eng. Remote Sens., 72, 249–260. https://doi.org/10.14358/PERS.72.3.249

The Land Processes Distributed Active Archive Center (LP DAAC) is responsible for the archive and distribution of NASA Making Earth System Data Records for Use in Research Environments (MEaSUREs) SRTM, which includes the global 1 arc second (~30 meter) combined (merged) image data product. (See User Guide Section 2.2.2) The combined image data set contains mosaicked one degree by one degree images/tiles of uncalibrated radar brightness values at 1 arc second. To create a smooth mosaic image, each pixel in an output is an average of all the image pixels for a location. Pixels with a value of zero (voids) were not counted. Because SRTM imaged a given location with two like-polarization channels (VV = vertical transmit and vertical receive, and HH = horizontal transmit and horizontal receive) and at a variety of look and azimuth angles, the quantitative scattering information was lost in the pursuit of a smoother image product unlike the SRTM swath image product SRTMIMGR, which preserved the quantitative scattering information. The NASA SRTM data sets result from a collaborative effort by the National Aeronautics and Space Administration (NASA) and the National Geospatial-Intelligence Agency (NGA - previously known as the National Imagery and Mapping Agency, or NIMA), as well as the participation of the German and Italian space agencies. This collaboration aims to generate a near-global digital elevation model (DEM) of Earth using radar interferometry. SRTM was the primary (and virtually only) payload on the STS-99 mission of the Space Shuttle Endeavour, which launched February 11, 2000 and flew for 11 days. The SRTM swaths extended from ~30 degrees off-nadir to ~58 degrees off-nadir from an altitude of 233 kilometers (km), creating swaths ~225 km wide, and consisted of all land between 60° N and 56° S latitude to account for 80% of Earth's total landmass. Known Issues * Known issues in the NASA SRTM are described in the following publication: * Rodriguez, E., C. S. Morris, and J. E. Belz (2006), A global assessment of the SRTM performance, Photogramm. Eng. Remote Sens., 72, 249–260. https://doi.org/10.14358/PERS.72.3.249

The Visible Infrared Imaging Radiometer Suite (VIIRS) Moderate Resolution Terrain Correction Geolocation (VJ203MODLL) Version 2.1 product from the NOAA-21 VIIRS sensor is produced in 6 minute temporal satellite increments (swaths) at 750 meter resolution. Intersecting the VIIRS line of sight vector with Earth’s geoid and the World Geodetic System (WGS) ellipsoid, this product is based on the SRTM30 Version 2 digital elevation model (DEM), which uses GTOPO30 data for areas from 60° North to 60° South. VJ203MODLL is a terrain correction geolocation product that provides the spatial location for various VIIRS data products. Each swath of data is approximately 3,060 kilometers along track (long) and 3,060 kilometers across track (wide). Provided in the VJ203MODLL product are variables for height, latitude, and longitude. These Science Data Sets (SDS) variables are used in conjunction with the VJ214 swath product for accurate geolocation information. Known Issues * The version for this product is listed incorrectly in the long name. The long name should read "VIIRS/JPSS2 Moderate Resolution Terrain Corrected Geolocation 6-Min L1 Swath 750m Light V021". This will be rectified in future versions. * For complete information about known issues please refer to the MODIS/VIIRS Land Quality Assessment website.

The Global Ecosystem Dynamics Investigation (GEDI) mission aims to characterize ecosystem structure and dynamics to enable radically improved quantification and understanding of the Earth’s carbon cycle and biodiversity. The GEDI instrument produces high resolution laser ranging observations of the 3-dimensional structure of the Earth. GEDI is attached to the International Space Station (ISS) and collects data globally between 51.6° N and 51.6° S latitudes at the highest resolution and densest sampling of any light detection and ranging (lidar) instrument in orbit to date. Each GEDI Version 3 granule encompasses one-fourth of an ISS orbit and includes georeferenced metadata to allow for spatial querying and subsetting. The GEDI instrument was removed from the ISS and placed into storage on March 17, 2023. No data were acquired during the hibernation period from March 17, 2023, to April 24, 2024. GEDI was re-instated on the ISS and resumed operations as of April 26, 2024. The GEDI Level 2B Canopy Cover and Vertical Profile Metrics product (GEDI02_B) extracts biophysical metrics from each GEDI waveform. These metrics are based on the directional gap probability profile derived from the L1B waveform. Metrics provided include canopy cover, Plant Area Index (PAI), Plant Area Volume Density (PAVD), and Foliage Height Diversity (FHD). The GEDI02_B product is provided in HDF5 format and has a spatial resolution (average footprint) of 25 meters. The GEDI02_B data product contains 209 layers/variables for each of the eight-beam ground transects (or laser footprints located on the land surface). Variables provided include precise latitude, longitude, elevation, height, canopy cover, and vertical profile metrics. Additional information for the variables can be found in the GEDI Level 2B Data Dictionary. Known Issues * Data acquisition gaps: GEDI data acquisitions were suspended on December 19, 2019 (2019 Day 353) and resumed on January 8, 2020 (2020 Day 8). * Known Issues: Section 8 of the User Guide provides additional information on known issues.

The Land Processes Distributed Active Archive Center (LP DAAC) is responsible for the archive and distribution of the NASA Making Earth System Data Records for Use in Research Environments (MEaSUREs) version SRTM, which includes the global 1 arc second (~30 meter) product. NASA Shuttle Radar Topography Mission (SRTM) datasets result from a collaborative effort by the National Aeronautics and Space Administration (NASA) and the National Geospatial-Intelligence Agency (NGA - previously known as the National Imagery and Mapping Agency, or NIMA), as well as the participation of the German and Italian space agencies. The purpose of SRTM was to generate a near-global digital elevation model (DEM) of the Earth using radar interferometry. SRTM was a primary component of the payload on the Space Shuttle Endeavour during its STS-99 mission. Endeavour launched February 11, 2000 and flew for 11 days. SRTM collected data in swaths, which extend from ~30 degrees off-nadir to ~58 degrees off-nadir from an altitude of 233 kilometers (km). These swaths are ~225 km wide, and consisted of all land between 60° N and 56° S latitude. This accounts for about 80% of Earth's total landmass. Each SRTMGL1 data tile contains a mosaic and blending of elevations generated by averaging all "data takes" that fall within that tile. These elevation files use the extension ".HGT", meaning height (such as N37W105.SRTMGL1.HGT). The primary goal of creating the Version 3 data was to eliminate voids that were present in earlier versions of SRTM data. In areas with limited data, existing topographical data were used to supplement the SRTM data to fill the voids. The source of each elevation pixel is identified in the corresponding SRTMGL1N product (such as N37W105.SRTMGL1N.NUM). The global 1 arc second SRTM product is also available in NetCDF4 format as the SRTMGL1_NC dataset with the source of each elevation pixel in the corresponding SRTMGL1_NUMNC product. Known Issues * Known issues in the NASA SRTM are described in the following publication: * Rodriguez, E., C. S. Morris, and J. E. Belz (2006), A global assessment of the SRTM performance, Photogramm. Eng. Remote Sens., 72, 249–260. https://doi.org/10.14358/PERS.72.3.249

The Land Processes Distributed Active Archive Center (LP DAAC) is responsible for the archive and distribution of the NASA Making Earth System Data Records for Use in Research Environments (MEaSUREs) version SRTM, which includes the global 1 arc second (~30 meter) product. NASA Shuttle Radar Topography Mission (SRTM) datasets result from a collaborative effort by the National Aeronautics and Space Administration (NASA) and the National Geospatial-Intelligence Agency (NGA - previously known as the National Imagery and Mapping Agency, or NIMA), as well as the participation of the German and Italian space agencies. The purpose of SRTM was to generate a near-global digital elevation model (DEM) of the Earth using radar interferometry. SRTM was a primary component of the payload on the Space Shuttle Endeavour during its STS-99 mission. Endeavour launched February 11, 2000 and flew for 11 days. SRTM collected data in swaths, which extend from ~30 degrees off-nadir to ~58 degrees off-nadir from an altitude of 233 kilometers (km). These swaths are ~225 km wide, and consisted of all land between 60° N and 56° S latitude. This accounts for about 80% of Earth's total landmass. Each SRTMGL1 data tile contains a mosaic and blending of elevations generated by averaging all "data takes" that fall within that tile. These elevation files use the extension ".HGT", meaning height (such as N37W105.SRTMGL1.HGT). The primary goal of creating the Version 3 data was to eliminate voids that were present in earlier versions of SRTM data. In areas with limited data, existing topographical data were used to supplement the SRTM data to fill the voids. The source of each elevation pixel is identified in the corresponding SRTMGL1N product (such as N37W105.SRTMGL1N.NUM). The global 1 arc second SRTM product is also available in NetCDF4 format as the SRTMGL1_NC dataset with the source of each elevation pixel in the corresponding SRTMGL1_NUMNC product. Known Issues * Known issues in the NASA SRTM are described in the following publication: * Rodriguez, E., C. S. Morris, and J. E. Belz (2006), A global assessment of the SRTM performance, Photogramm. Eng. Remote Sens., 72, 249–260. https://doi.org/10.14358/PERS.72.3.249

The NOAA-20 Visible Infrared Imaging Radiometer Suite (VIIRS) Water Reservoir 8-day Level 3 (L3) Global (VJ128C2) Version 2 product provides current data for 151 man-made reservoirs and 13 regulated natural lakes for a total of 164 reservoirs. The VJ128C2 data product provides an 8-day time series of surface area, elevation, and water storage. Datasets are combined with pre-established Area-Elevation (A-E) curves and image classifications of near-infrared (NIR) reflectance from the surface reflectance product acquired by the VIIRS satellite (VJ109H1). The VJ128C2 data product consists of a single variable with information about the reservoir identifier, dam location (longitude and latitude), reservoir surface area, elevation, and water storage capacity. Known Issues * Water occurrence images generally show smaller surface area dynamics in high latitude regions, creating pixels with low occurrence values that have relatively large uncertainties. In addition, the quality of raw water area classification can be affected by lake ice coverage typically creating an overestimation of surface area in the enhancement algorithm. This issue will be addressed in a future release of the enhancement algorithm. For additional information about known issues, refer to Section 4 in the User Guide.

The Terra Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) Global Digital Elevation Model (GDEM) Version 3 (ASTGTM) provides a global digital elevation model (DEM) of land areas on Earth at a spatial resolution of 1 arc second (approximately 30 meter horizontal posting at the equator). The development of the ASTER GDEM data products is a collaborative effort between National Aeronautics and Space Administration (NASA) and Japan's Ministry of Economy, Trade, and Industry (METI). The ASTER GDEM data products are created by the Sensor Information Laboratory Corporation (SILC) in Tokyo. The ASTER GDEM Version 3 data product was created from the automated processing of the entire ASTER Level 1A archive of scenes acquired between March 1, 2000, and November 30, 2013. Stereo correlation was used to produce over one million individual scene based ASTER DEMs, to which cloud masking was applied. All cloud screened DEMs and non-cloud screened DEMs were stacked. Residual bad values and outliers were removed. In areas with limited data stacking, several existing reference DEMs were used to supplement ASTER data to correct for residual anomalies. Selected data were averaged to create final pixel values before partitioning the data into 1 degree latitude by 1 degree longitude tiles with a one pixel overlap. To correct elevation values of water body surfaces, the ASTER Global Water Bodies Database (ASTWBD) Version 1 data product was also generated. The geographic coverage of the ASTER GDEM extends from 83° North to 83° South. Each tile is distributed in both a Cloud Optimized GeoTIFF (COG) and NetCDF4 format through NASA Earthdata Search. Data are projected on the 1984 World Geodetic System (WGS84)/1996 Earth Gravitational Model (EGM96) geoid. Each of the 22,912 tiles in the collection contain at least 0.01% land area. Provided in the ASTER GDEM product are layers for DEM and number of scenes (NUM). The NUM layer indicates the number of scenes that were processed for each pixel and the source of the data. While the ASTER GDEM Version 3 data products offer substantial improvements over Version 2, users are advised that the products still may contain anomalies and artifacts that will reduce its usability for certain applications. Known Issues * ASTER GDEM Version 3 tiles overlap by one pixel to the north, south, east, and west of the tile perimeter. In most cases the overlapping edge pixels have identical pixel values, but it is possible that in some instances values will differ. * ASTER GDEM Version 3 is considered to be void free except for Greenland and Antarctica. * Users are reminded that because there are known inaccuracies and artifacts in the dataset, to use the product with awareness of these limitations. The data are provided "as is" and neither NASA nor METI/Earth Resources Satellite Data Analysis Center (ERSDAC) will be responsible for any damages resulting from use of the data.

The Land Processes Distributed Active Archive Center (LP DAAC) is responsible for the archive and distribution of the NASA Making Earth System Data Records for Use in Research Environments (MEaSUREs) Digital Elevation Model (DEM) version 1 (NASADEM_HGT) dataset, which provides global elevation data at 1 arc second spacing. NASADEM data products were derived from original telemetry data from the Shuttle Radar Topography Mission (SRTM), a collaboration between NASA and the National Geospatial-Intelligence Agency (NGA), as well as participation from the German and Italian space agencies. SRTM's primary focus was to generate a near-global DEM of the Earth using radar interferometry. It was a primary component of the payload on space shuttle _Endeavour_ during its STS-99 mission, which was launched on February 11, 2000, and flew for 11 days. In addition to Terra Advanced Spaceborne Thermal and Reflection Radiometer (ASTER) Global Digital Elevation Model (GDEM) Version 2 data, NASADEM also relied on Ice, Cloud, and Land Elevation Satellite (ICESat) Geoscience Laser Altimeter System (GLAS) ground control points of its lidar shots to improve surface elevation measurements that led to improved geolocation accuracy. Other reprocessing improvements include the conversion to geoid reference and the use of GDEMs and Advanced Land Observing Satellite Panchromatic Remote-sensing instrument for Stereo Mapping (PRISM) AW3D30 DEM, and interpolation for void filling. NASADEM are distributed in 1 degree latitude by 1 degree longitude tiles and consist of all land between 60° N and 56° S latitude. This accounts for about 80% of Earth's total landmass. NASADEM_HGT data product layers include DEM, number of scenes (NUM), and an updated SRTM water body dataset (water mask). The NUM layer indicates the number of scenes that were processed for each pixel and the source of the data. A low-resolution browse image showing elevation is also available for each NASADEM_HGT granule. The global 1 arc second NASADEM product is also available in NetCDF4 format as the NASADEM_NC dataset with the source of each elevation pixel in the corresponding NASADEM_NUMNC product.

Level 1GST is terrain corrected and provided in 16-bit radiance values.

Level 1T is precision terrain correction by incorporating ground control points from the GLS2005 dataset. Scenes with sufficient ground control data and satisfactory RMS error are processed to Level 1T.

Level 1GST is terrain corrected and provided in 16-bit radiance values.

Rural land area below 5m is the percentage of total land where the rural land elevation is 5 meters or less.

The Land Processes Distributed Active Archive Center (LP DAAC) is responsible for the archive and distribution of NASA Making Earth System Data Records for Use in Research Environments (MEaSUREs) Digital Elevation Model (DEM) version 1 (NASADEM_SSP) dataset, which provides global Shuttle Radar Topography Mission (SRTM) sub-swath elevation data at 1 arc second spacing. NASADEM data products were derived from original telemetry data from the Shuttle Radar Topography Mission (SRTM), a collaboration between NASA and the National Geospatial-Intelligence Agency (NGA), as well as participation from the German and Italian space agencies. SRTM's primary focus was to generate a near-global DEM of the Earth using radar interferometry. It was a primary component of the payload on space shuttle _Endeavour_ during its STS-99 mission, which was launched on February 11, 2000, and flew for 11 days. In addition to Terra Advanced Spaceborne Thermal and Reflection Radiometer (ASTER) Global Digital Elevation Model (GDEM) Version 2 data, NASADEM also relied on Ice, Cloud, and Land Elevation Satellite (ICESat) Geoscience Laser Altimeter System (GLAS) ground control points of its lidar shots to improve surface elevation measurements that led to improved geolocation accuracy. Other reprocessing improvements include the conversion to geoid reference and the use of GDEMs and Advanced Land Observing Satellite Panchromatic Remote-sensing Instrument for Stereo Mapping (PRISM) AW3D30 DEM, and interpolation for void filling. NASADEM are distributed in 1 degree latitude by 1 degree longitude tiles and consist of all land between 60° N and 56° S latitude. This accounts for about 80% of Earth's total landmass. NASADEM_SSP data product layers include radar total correlation, radar volumetric correlation, radar individual images, radar incidence angle (relative to ellipsoid), and radar incidence angle (local). A low-resolution browse image showing sub-swath elevation is also available for each NASADEM_SSP granule.

The Terra Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) Global Water Bodies Database (ASTWBD) Version 1 data product provides global coverage of water bodies larger than 0.2 square kilometers at a spatial resolution of 1 arc second (approximately 30 meters) at the equator, along with associated elevation information. The ASTWBD data product was created in conjunction with the ASTER Global Digital Elevation Model (ASTER GDEM) Version 3 data product by the Sensor Information Laboratory Corporation (SILC) in Tokyo. The ASTER GDEM Version 3 data product was generated using ASTER Level 1A scenes acquired between March 1, 2000, and November 30, 2013. The ASTWBD data product was then generated to correct elevation values of water body surfaces. To generate the ASTWBD data product, water bodies were separated from land areas and then classified into three categories: ocean, river, or lake. Oceans and lakes have a flattened, constant elevation value. The effects of sea ice were manually removed from areas classified as oceans to better delineate ocean shorelines in high latitude areas. For lake water bodies, the elevation for each lake was calculated from the perimeter elevation data using the mosaic image that covers the entire area of the lake. Rivers presented a unique challenge given that their elevations gradually step down from upstream to downstream; therefore, visual inspection and other manual detection methods were required. The geographic coverage of the ASTWBD extends from 83°N to 83°S. Each tile is distributed in GeoTIFF format and referenced to the 1984 World Geodetic System (WGS84)/1996 Earth Gravitational Model (EGM96) geoid. Each data product is provided as a zipped file that contains an attribute file with the water body classification information and a DEM file, which provides elevation information in meters.

The Terra Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) Global Digital Elevation Model (GDEM) Version 3 (ASTGTM) provides a global digital elevation model (DEM) of land areas on Earth at a spatial resolution of 1 arc second (approximately 30 meter horizontal posting at the equator). The development of the ASTER GDEM data products is a collaborative effort between National Aeronautics and Space Administration (NASA) and Japan's Ministry of Economy, Trade, and Industry (METI). The ASTER GDEM data products are created by the Sensor Information Laboratory Corporation (SILC) in Tokyo. The ASTER GDEM Version 3 data product was created from the automated processing of the entire ASTER Level 1A archive of scenes acquired between March 1, 2000, and November 30, 2013. Stereo correlation was used to produce over one million individual scene based ASTER DEMs, to which cloud masking was applied. All cloud screened DEMs and non-cloud screened DEMs were stacked. Residual bad values and outliers were removed. In areas with limited data stacking, several existing reference DEMs were used to supplement ASTER data to correct for residual anomalies. Selected data were averaged to create final pixel values before partitioning the data into 1 degree latitude by 1 degree longitude tiles with a one pixel overlap. To correct elevation values of water body surfaces, the ASTER Global Water Bodies Database (ASTWBD) Version 1 data product was also generated. The geographic coverage of the ASTER GDEM extends from 83° North to 83° South. Each tile is distributed in both a Cloud Optimized GeoTIFF (COG) and NetCDF4 format through NASA Earthdata Search. Data are projected on the 1984 World Geodetic System (WGS84)/1996 Earth Gravitational Model (EGM96) geoid. Each of the 22,912 tiles in the collection contain at least 0.01% land area. Provided in the ASTER GDEM product are layers for DEM and number of scenes (NUM). The NUM layer indicates the number of scenes that were processed for each pixel and the source of the data. While the ASTER GDEM Version 3 data products offer substantial improvements over Version 2, users are advised that the products still may contain anomalies and artifacts that will reduce its usability for certain applications. Known Issues * ASTER GDEM Version 3 tiles overlap by one pixel to the north, south, east, and west of the tile perimeter. In most cases the overlapping edge pixels have identical pixel values, but it is possible that in some instances values will differ. * ASTER GDEM Version 3 is considered to be void free except for Greenland and Antarctica. * Users are reminded that because there are known inaccuracies and artifacts in the dataset, to use the product with awareness of these limitations. The data are provided "as is" and neither NASA nor METI/Earth Resources Satellite Data Analysis Center (ERSDAC) will be responsible for any damages resulting from use of the data.

The Global Ecosystem Dynamics Investigation (GEDI) mission aims to characterize ecosystem structure and dynamics to enable radically improved quantification and understanding of the Earth’s carbon cycle and biodiversity. The GEDI instrument produces high resolution laser ranging observations of the 3-dimensional structure of the Earth. GEDI is attached to the International Space Station (ISS) and collects data globally between 51.6° N and 51.6° S latitudes at the highest resolution and densest sampling of any light detection and ranging (lidar) instrument in orbit to date. Each GEDI Version 3 granule encompasses one-fourth of an ISS orbit and includes georeferenced metadata to allow for spatial querying and subsetting. The GEDI instrument was removed from the ISS and placed into storage on March 17, 2023. No data were acquired during the hibernation period from March 17, 2023, to April 24, 2024. GEDI was reinstated on the ISS and resumed operations as of April 26, 2024. The GEDI Level 1B Geolocated Waveforms product (GEDI01_B) provides geolocated corrected and smoothed waveforms, geolocation parameters, and geophysical corrections for each laser shot for all eight GEDI beams. GEDI01_B data are created by geolocating the GEDI01_A raw waveform data. The GEDI01_B product is provided in HDF5 format and has a spatial resolution (average footprint) of 25 meters. The GEDI01_B data product comprises 97 layers/variables for each of the eight beams, encompassing geolocated corrected and smoothed waveform datasets, associated parameters, as well as ancillary, geolocation, and geophysical correction information. Known Issues * Data acquisition gaps: GEDI data acquisitions were suspended on December 19, 2019 (2019 Day 353) and resumed on January 8, 2020 (2020 Day 8). * Known Issues: Section 8 of the User Guide provides additional information on known issues.

The delivery of all Suomi National Polar-orbiting Partnership (Suomi NPP) VIIRS science data products will cease on November 2, 2026 (2026/306). Data users are encouraged to transition to the equivalent VJ203MODLL (primary) or VJ103MODLL (secondary) data products. The Visible Infrared Imaging Radiometer Suite (VIIRS) Moderate Resolution Terrain Correction Geolocation (VNP03MODLL) Version 2 product from the NASA/NOAA Suomi National Polar-orbiting Partnership (Suomi NPP) VIIRS sensor is produced in 6 minute temporal satellite increments (swaths) at 750 meter resolution. Intersecting the VIIRS line of sight vector with Earth’s geoid and the World Geodetic System (WGS) ellipsoid, this product is based on the SRTM30 Version 2 digital elevation model (DEM), which uses GTOPO30 data for areas from 60° North to 60° South. VNP03MODLL is a terrain correction geolocation product that provides the spatial location for various VIIRS data products. Each swath of data is approximately 3,060 kilometers along track (long) and 3,060 kilometers across track (wide). Provided in the VNP03MODLL product are layers for height, latitude, and longitude. These Science Data Sets (SDS) layers / Variables are used in conjunction with the VNP14 swath product for accurate geolocation information. Known Issues * For complete information about known issues please refer to the MODIS/VIIRS Land Quality Assessment website.